Skip to content
‹ Back to IndustriesBuilding Management

Layout and exhaust choices changed modeled infection risk nearly tenfold in an ABSL-3 lab

A Building and Environment study compared two ABSL-3 labs built to the same biosafety standard and ventilation specifications but with different equipment layouts. The A12-UL setup (double-sided dispersed layout with upper supply and low exhaust) showed a breathing-zone infection probability nearly an order of magnitude lower than A10-UU (single-sided centralized layout with upper supply and upper exhaust). The findings suggest that moving or installing equipment can change exposure conditions even when air change rates and ventilation parameters are unchanged.

This story was produced through MarketScale. See how Building Management teams put it to work with Customer Stories & Case Studies.

By MarketScale Newsroom · Absl-3 LaboratoryBiosafety CabinetsLaboratory VentilationAerosol Exposure
Share
Layout and exhaust choices changed modeled infection risk nearly tenfold in an ABSL-3 lab

Key takeaways

01

The ventilation scheme that cleared suspended aerosol fastest overall was not the one that steered it out most directly, so a single decay or air-change figure can miss where exposure actually happens.

02

Floors and downstream walls collected the most bioaerosol, and which wall counts as downstream can change whenever a cage rack, cabinet or exhaust grille moves.

Free workspace

Turn your Building Management expertise into content.

Record interviews, organize footage, and write with AI on a free trial of the MarketScale platform for qualifying companies. No demo required, no credit card.

Try it Free

Two rooms with similar ventilation specifications can perform differently once equipment is installed. A study published in Building and Environment found that one combination, A12-UL, a double-side dispersed layout with upward supply and low exhaust, produced a breathing-zone infection probability nearly an order of magnitude lower than A10-UU, which paired a single-sided centralized layout with upward supply and upward exhaust.

The comparison is cleaner than most. The authors chose two ABSL-3 laboratories with identical structural parameters, ventilation characteristics and air exchange rates. Because the air changes were held equal, the nearly tenfold gap points to where the equipment sat and where the air left the room, not to how much air the system moved.

That puts the question on the desk of whoever approves moving a cage rack or adding a biosafety cabinet. Lab Manager associate editor Michelle Gaulin, covering the paper on November 18, put the management lesson plainly: installing or relocating an instrument can change a room's environment even when nobody has touched the building's ventilation. For a biosafety officer or lab facilities director, the practical issue is whether an equipment move gets reviewed like a ventilation change.

Two labs, three airflow schemes, six test cases

Yongxin Wang and Zhijian Liu were among the authors of the paper, which appears in the journal's Volume 305, Part A, dated November 1, 2026. They examined two ABSL-3 laboratories, both designed and built to comply with GB 19489, The general requirements of biosafety laboratories. Each lab arranged its equipment differently. In the A10 lab, equipment was grouped on one side near the air supply in a single-sided centralized layout, and the opposite side was left clear. In the A12 lab, the biosafety cabinet and the animal cages sat on opposite sides of the supply and exhaust vents, which made it a double-sided dispersed arrangement.

The scenario being modeled is the bad day, not the routine one. Accidental operations, equipment failures or spills can still produce a substantial number of bioaerosols in a high-level lab, the authors write, and those micron-sized particles can stay suspended and travel with the airflow to workers' airways. In an ABSL-3 lab, as Lab Manager notes, directional airflow and contaminant removal are part of the containment strategy. The path air takes inside the room is therefore a containment question, not a comfort setting.

Animal labs add a complication. Individually ventilated cages and biosafety cabinets occupy a significant share of the space, and the authors describe them as internal boundaries that compress the effective flow cross-section and alter the airflow path the designers intended. Earlier work had simulated airflow uniformity for different cage layouts without following full-room aerosol spread, or examined biosafety cabinets under a single ventilation mode. This paper's contribution is to test both layouts against several ventilation schemes.

Each layout was paired with three ventilation schemes: upper supply with upper exhaust (UU), upper supply with low exhaust (UL), and upper supply with both upper and low exhaust (UUL). The team released a Serratia marcescens tracer, sampled concentrations at multiple points with an Andersen sampler to validate a computer airflow model, then used the model to track how the aerosol spread, decayed and settled, and what it meant for exposure at seated and standing breathing heights.

How the ABSL-3 comparison was set up

2 layouts
Clustered on one side (A10) versus dispersed across both sides (A12), in otherwise matched rooms
3 schemes
Exhaust high, low, or both, all with ceiling-level supply
6 conditions
Every layout tested against every ventilation scheme
2 heights
Exposure estimated at seated and standing breathing zones

Building and Environment (Elsevier)

The headline mechanism is a division of labor. The ventilation scheme set the room's overall flow pattern, the authors found, while the equipment created local disturbances at its own edges.

Put simply, the mechanical drawings describe the big loop and the equipment plan decides where the eddies form. Those eddies sit right next to the cabinets and cages where staff do their work. The earlier flow-field studies the authors cite suggest where trouble collects: the leeward side of large instruments may become a primary region for aerosol accumulation.

Fastest clearing versus best-aimed exhaust

Here is the result that should complicate a commissioning report. The UU scheme, with upward supply and upward exhaust, had the highest overall aerosol decay coefficient; the abstract gives values of 0.02380 and 0.02427. That suggests it cleared suspended aerosol from the room fastest. But the UL scheme, with upward supply and low exhaust, had the best directional exhaust efficiency, which the authors say limits aerosol diffusion.

A room can dilute aerosol quickly on average and still carry it past people's faces on the way out. The A12 pairing with low exhaust kept the high-risk zone confined to the area downstream of the release point.

The earlier ventilation research the authors cite, from clean rooms and hospital isolation wards, gives the split a familiar shape. Upper supply with lower exhaust can achieve piston-like directional removal of pollutants, while upper supply with upper exhaust tends to form large-scale circulation and pollutant recirculation. One plausible reading is that a recirculating loop could keep the room-wide average falling quickly while still sweeping aerosol back through occupied space. A piston-like flow pushes it one way, toward the exit.

The size of the low-exhaust advantage differs inside the paper itself. The abstract reports a 33.32 percent improvement in directional exhaust efficiency over UU, while the journal's highlights state 38 percent, the figure Lab Manager cited as about 38 percent. Either way, it is a comparison between schemes within this study, not a standalone performance rating.

For labs that judge ventilation performance mainly by air change rate or clearance time, this suggests those figures can rank rooms differently from how exposure does. A room's decay figure answers how fast the aerosol goes away. It doesn't tell anyone where the aerosol travels while it's leaving. The authors framed their goal as finding the combination that balances rapid self-purification with low exposure risk, which treats them as two separate targets from the start.

Where the result stops applying

Two rooms in one ABSL-3 facility, designed to one national standard, is a narrow base. Lab Manager says directly that the exhaust efficiency gain should not be treated as a universal design target or copied into other rooms without testing.

A related study from Liu and colleagues, published in Energy and Built Environment in June 2026, gives another reason to treat any single result as specific to its room. In a BSL-2 laboratory, with simulations checked against experiments, that team found airflow distribution was a key factor in removing bioaerosols and that infection risk varied with where the aerosol was released. The ABSL-3 finding describes a high-risk zone downstream of one release point. A leak elsewhere in the room could put a different area downstream.

What carries over is the method: judge the layout and the ventilation together. That doesn't produce a ranking of exhaust heights.

Treating a cage rack move like a ventilation change

Lab Manager's guidance turns the finding into a review process. Before substantial equipment is installed or relocated, it recommends bringing in facilities staff, biosafety professionals, the people who use the room and qualified ventilation specialists. The review should cover the equipment's dimensions, heat output, exhaust needs, maintenance clearances, workflow, decontamination needs and distance from supply diffusers and exhaust grilles. Biosafety cabinets need extra care, because doors, foot traffic, fans and drafts can disrupt their inflow.

The reason for that long list is how many ways equipment interacts with a room. A unit can release heat, obstruct an exhaust path, interfere with cleaning or change how employees move through the space. Those interactions, the outlet argues, make layout part of the lab's risk-management process rather than a question of space efficiency alone. The high-containment design guidance it cites draws a similar link among ventilation, equipment heat loads, personnel density, containment devices and workflow.

The cabinet point matters because so much of the protection model depends on the cabinet working as designed. In UK Health Security Agency tests of 36 common microbiological procedures, published in Applied Biosafety in 2022, aerosol concentrations ranged from 0 to 13,000 cfu/m3. The risk assessment found any aerosol from those processes would be contained within a correctly operating biological safety cabinet. "Correctly operating" is the condition that drafts and foot traffic near the cabinet put at risk, which is why Lab Manager says cabinet placement belongs in planning, not after installation.

A documented management-of-change process, in that framing, decides whether a move calls for updated drawings, airflow testing, room rebalancing, smoke visualization, cabinet recertification or a revised biosafety risk assessment. Performance then gets checked after installation instead of trusting the design review alone.

Some institutions already write change triggers into their safety paperwork on the chemical side. The University of Pennsylvania's Chemical Hygiene Plan requires the principal investigator to complete the lab hazard assessment questionnaire each year, when research conditions change, or when new hazards are introduced. A committee drafting its own rule could use the same structure, with a substantial equipment relocation listed as one of the changes that triggers a fresh review.

Whether a cage rack move counts as a change that calls for a fresh risk assessment is a call each institution makes. The ABSL-3 data give biosafety committees a documented reason to say it does.

Cleaning plans follow the airflow

Cleaning plans are the other place the finding lands. Floors and downstream walls were the main deposition sites for bioaerosol in the study, and Lab Manager adds hard-to-reach spots behind equipment to the list. Because downstream is defined by the airflow, moving a rack or an exhaust grille could change which wall needs the most attention.

The earlier BSL-2 work from Liu's group points the same way. Nearly 70 percent of all bioaerosols in that study were deposited on surfaces such as walls, equipment and people, and a significant portion entered the biosafety cabinet's operating area through the front window opening, which the authors flagged as a potential cross-infection risk. That team presented its results as guidance on where to disinfect first. The ABSL-3 deposition map could be used the same way, as long as the map is redrawn when the layout changes.

Before signing off on a move, ask two things: after the move, which wall sits downstream of the main work zone, and do the smoke test and the decontamination plan reflect that wall?

For operators who run upper-only exhaust with equipment concentrated near the supply side, the results suggest a second look, since that pairing had breathing-zone infection probability nearly an order of magnitude higher than dispersed equipment with low exhaust. Whether that pattern holds outside one ABSL-3 facility is something post-move smoke tests and airflow checks can answer room by room.

Featured companies

Your experts belong here

Every story in MarketScale Building Management starts with a company putting its facilities engineers, energy managers, and service technicians on the record. Buyers are already reading this topic. The only question is whose experts they find.

Owners and facilities teams pick on trust, and your engineers turn that trust into inbound conversations.

Book DemoSee how it works15 minutes, straight to a calendar.

About the author

MarketScale Newsroom
MarketScale NewsroomEditorial Team, MarketScale

The MarketScale Newsroom reports on the companies, technologies, and trends shaping 16 B2B industries. It turns primary sources and expert commentary into clear, useful coverage for the people doing the work.

B2B Weekly

The week in Building Management, and sixteen other industries, every Monday.

Ten stories, one-line takes, five minutes. Free.

Building Management: are you visible to AI?

Before they reach out, Building Management buyers ask AI engines which vendors to trust. Explore how your experts, customers, and partners can become useful content for buyers and AI search.

Free Trial

You just read one Building Management expert. Your company is full of them.

This article was produced through MarketScale. The same platform turns your facilities engineers, energy managers, and service technicians into the articles, video, and social content Building Management buyers are searching for. Start a free trial and see it with your own people. For qualifying companies, no credit card, no demo required.

NPS +73 · 1,000+ creators · 38+ countries

What your free trial includes

Hands-on access to the MarketScale platform
Media requests to your crowd, remote recording, AI writing tools
No demo required. No credit card.
For qualifying companies. Company confirmation required.

More Building Management Insights

A Linux Foundation coalition group is drafting Division 25 bid language for open controls

A Linux Foundation coalition group is drafting Division 25 bid language for open controls

The Coalition for Smarter Buildings, a Linux Foundation project, is drafting standard Division 25 bid language so owners can require open, interoperable building controls. Related open-licensed GitHub specs and tools cover data ingestion, semantic models and control testing. The editorial argues interoperability gets decided at bid time.

  • 01Sinclair argues interoperability gets decided in bid documents long before open-source code is downloaded, making Div2525’s Division 25 spec language a first step owners can act on.
  • 02Owners and consulting engineers can shape the specs without coding: working groups take naming conventions, procurement language and operational workflows, and joining takes a free GitHub account and a Linux Foundation ID.
  • 03A sharper question for the next controls bid: will the deliverable include a validated semantic model and control sequences an engineer can simulate before startup?

Nov 18, 2026

Yale study models plant wall needing 363 modules to reach outdoor CO2

Yale study models plant wall needing 363 modules to reach outdoor CO2

Tuning matters most. In Yale's living-wall study, adjusting lighting and airflow direction produced a 43-fold improvement in the system's ability to remove CO2, so facilities and HVAC teams should specify living walls the way they specify air-handling equipment.

  • 01Typical HVAC systems dilute indoor CO2 with outdoor air, so they cannot bring indoor levels below outdoor levels, which typically hover at about 428 ppm in the US, according to NOAA monitoring data. A plant-based system that removes CO2 could get a room below that.
  • 02A plant wall's CO2 performance varied 43-fold depending on lighting and airflow direction, so fan orientation and light intensity belong in the spec, along with the plant count.
  • 03Before buying a plant wall for air quality, ask for measured CO2 removal per module, the direction air moves through the root zone, and the light level the figures assume.

Nov 18, 2026

ASHRAE Guideline 43: a nine-step path to a hospital VMP

ASHRAE Guideline 43: a nine-step path to a hospital VMP

Guideline 43 asks hospitals to document how their HVAC actually runs, and a new Standard 170 addendum signals a shift toward risk-assessed operations.

  • 01Standard 170 sets what an operating room must be able to do; a Ventilation Management Program records who decided what it actually does after hours, and on what evidence.
  • 02The 2027 NFPA 99 recognizes HVAC Ventilation Management Programs in Chapter 9, and a September 2026 Standard 170 addendum requires a risk assessment before operating room ventilation is adjusted.
  • 03For hospitals whose inspectors still enforce older editions, the first useful step is confirming in writing which Standard 170 edition applies, since every later rule in the program depends on it.

Nov 17, 2026

Explore More Building Management Insights

Read more expert perspectives from across Building Management.

Browse Building Management Hub

About the Expert

MarketScale Newsroom
MarketScale Newsroom

Editorial Team

MarketScale

The MarketScale Newsroom reports on the companies, technologies, and trends shaping 16 B2B industries. It turns primary sources and expert commentary into clear, useful coverage for the people doing the work.

For B2B teams

Your experts could be publishing here

Stories like this one run on content MarketScale captures from real practitioners. See how your team's expertise becomes coverage in Building Management and beyond.

Book a Demo

Or call us. No forms required. We pick up. 214-945-2512