# MIT voxel blocks let imprecise robots build load-bearing demos

By MarketScale Newsroom · Published 2026-11-22 · Engineering & Construction on MarketScale
Canonical: https://www.marketscale.com/industries/engineering-and-construction/mit-blocks-let-robots-with-10-millimeters-of-error-build-load-bearing-structures

> Miana Smith’s voxels are designed to absorb placement error so low-cost robots can assemble room-scale, load-bearing demos. Next up: concrete formwork.

## Key points

- Putting the accuracy in the block lets a robot miss by about 10 millimeters and still assemble load-bearing demos; that tolerance is about 100× looser than typical industrial arms (an illustrative ratio from the reported figures, not a measured claim).
- Cheap robots shift the hard part into the component: the voxel approach depends on producing complex lattice blocks economically, and Smith’s focus on automating their production suggests she sees that as the key hurdle.

On most factory floors, a robot that misses its mark by 10 millimeters gets pulled for recalibration. Industrial arms typically hold tolerances near 100 microns. In Miana Smith's lab at MIT's Center for Bits and Atoms, a 10-millimeter miss is just what the robots do, and the structures still go up load-bearing.

MIT News profiled the work on November 18. Smith, who has three MIT degrees (’21, SM ’23, PhD ’26), finished her PhD this year and stays on as a visiting researcher with the Center for Bits and Atoms team in MIT's Program in Media Arts and Sciences. She designs lattice blocks, which her lab calls voxels, that snap together and absorb placement error as the structure grows. The profile notes that a 10-millimeter margin would look like a failure to most engineers. Here it lets her robots cost a few hundred dollars apiece instead of tens of thousands.

Set the two reported tolerances side by side and the gap is about a factor of 100: 10 millimeters is 10,000 microns, against roughly 100 microns for a typical industrial arm. That ratio is this article's own arithmetic on the two figures MIT News reported. It's a way to picture the gap, not a measured performance claim.

For anyone at a contractor or developer weighing construction automation, the work changes which question comes first. Instead of asking how accurate a machine is, ask how much error the parts can tolerate.

## The precision tax on efficient buildings

Engineers already know how to use less material. The MIT News piece, written by Sydney Campbell of MIT's Office of Graduate Education, points to steel-framed buildings, where an estimated 30 to 40 percent of the steel could come out without weakening the frame if beam cross sections were customized. It rarely happens. Custom parts need one-off design and engineering, the manufacturing is often impractically expensive, and installing them on site takes highly skilled labor. So oversized, uniform members win, because they're cheaper to make and assemble at scale.

Digital fabrication was meant to narrow that gap. With 3D printing and robotic assembly, a complex design no longer has to cost more to produce. Those tools carry their own costs, though. Placing framing members or extruding concrete over a 10-meter span frequently calls for a machine with accuracy of a few millimeters, and equipment that precise is difficult to build and costly to purchase.

Look at it that way and the extra steel in a typical frame comes from manufacturing and labor, since the design knowledge already exists. Any fix has to make complexity cheap to build. Making it cheap to draw doesn't help.

Block Field

## How a block corrects its robot

Smith reverses the typical arrangement. Conventional systems combine simple material with a precise machine. Hers combines complex material with a simple, imprecise machine. She likens it to Lego. A child builds very imprecisely, but the finished Lego model still comes out precise. As she told MIT News, that is because the bricks are designed with clever mechanics that stop errors from adding up as the structure gets bigger.

Getting there took a structural change. For a long time her team built with small units that each needed as many as 24 connectors. Every joint was another chance for weakness or a failed placement, and that kept robots from building anything large. The fix, which Smith has described as almost embarrassingly obvious, was to make the blocks bigger and attach as many internal joints as possible before a robot ever picks one up. She calls the result a structurally active error-correction feature, the thing that lets robots build big and still carry load.

The lattice changed too. The team moved to a more heavily interconnected, stretch-dominated geometry, which Smith says beats a bending-dominated lattice on weight-to-stiffness and weight-to-strength. One joint design now works across plywood, bio-based plastics, aluminum and steel. The plywood version pairs Baltic birch with 3D-printed, compostable bio-based plastic, which Smith describes as a low-embodied-carbon way to make structural units from fairly standard construction materials.

According to MIT News, changing the material, the fabrication process and the lattice density within that common joint produces voxels with different properties. The outlet adds that since the system does not depend on any single material, architectural ambition need not be sacrificed. For a designer, this suggests material could become a project-by-project choice within one assembly system, rather than a reason to change systems.

Block Field

## Why many cheap robots can beat one precise one

Cheap robots bring a second benefit that matters on a schedule. A few hundred dollars per unit means many robots can work in parallel, where one expensive, precise machine would do everything slowly. The block carries the accuracy, so the robot can miss by about 10 millimeters and still build something load-bearing.

Smith's route to that idea ran through some unlikely places. In high school she rebuilt motorcycle engines through her school's STEM program and did electrical engineering work at a plasma physics lab at UCLA. While an MIT mechanical engineering undergraduate, she took a research position with architecture professor Larry Sass that introduced her to digital fabrication for buildings. Then came class 4.140, How to Make (almost) Anything, taught by Center for Bits and Atoms director Neil Gershenfeld, later her PhD advisor. There she became captivated by the notion that the whole world, buildings among it, might be assembled from an engineering version of Lego bricks.

Smith spent two years working with living systems in another Media Lab group before she moved into robotics. In that work she engineered bacteria into woven textile fibers, and she sent honeybees into microgravity to see whether they could survive. They did. She says that living organisms are, at their core, distributed assembly systems as well. By her account, that realization is what led her from small bugs to robots.

That background helps explain where the design puts its effort. In a distributed assembly system the accuracy has to live in the parts, so adding agents adds capacity without adding precision. For a builder, it suggests throughput would scale by adding inexpensive units rather than by buying a faster, more accurate machine. That's a different capital decision from the one industrial automation usually presents.

The strongest objection is that the cost doesn't disappear. It moves. A complex block has to be manufactured, and the economics hold only if voxels can be produced as cheaply as the robots that place them. Smith's own focus on automating production suggests she sees that as the real problem to solve, and it's the line item a buyer would need to see priced before anything else.

## Checking the 80 percent claim

Smith estimates that buildings made this way could cut embodied carbon by roughly 80 percent compared with standard concrete construction. The baseline is big. MIT News notes construction is often credited with more than a third of global greenhouse gas emissions, mostly because buildings use more material than they need.

Other tallies land in the same range. The Global Status Report figures compiled in Wikipedia's green building entry put buildings at 37 percent of global energy use and energy-related CO2 emissions as of 2020, and at 39 percent of global CO2 emissions once the manufacturing of building materials is counted. Material production is the part of that total the voxel approach targets. So the comparison point Smith chose, standard concrete construction, matters as much as the percentage itself.

Treat the 80 percent as a researcher's estimate, not a measured result from a finished building. So far the demonstrations are room-scale plywood structures, and outdoor testing is still ahead. Teams setting embodied-carbon targets can watch the figure, but it isn't ready for a procurement spec.

## From Bhutan housing to concrete formwork

The first field partner is Druk Holding and Investments, a major Bhutanese company focused on building a sustainable economy. The work is for its next housing development at Gelephu Mindfulness City. Bhutanese officials wanted construction methods that use local materials and can be reconfigured over time, which Smith saw as a natural fit for the voxel work. Her team has built room-scale, load-bearing demonstrations from plywood blocks, including a small house, and plans to test the system outdoors at a similar scale.

The commercial target is concrete. Smith hopes the same reconfigurable block logic can be used for formwork, so concrete can be shaped more efficiently. Complex molds are very expensive, and she expects a reconfigurable system to bring that expense down by a wide margin. Smith says she wants to know that her work makes a difference. In her view, everyone in her generation, at the very least, regards the climate crisis as the doom that lies ahead.

She's starting a company around sustainable concrete construction through an Activate Fellowship, a science entrepreneurship program that helps researchers commercialize their work. Gershenfeld has said he didn't first see her as an entrepreneur but now considers her the best kind, driven by the change she wants to make more than by a business plan.

Formwork is where general contractors and concrete subcontractors would feel this first. That's especially true for those whose margins on complex geometry depend on custom molds that get used once and thrown away. A reusable, robot-assembled mold system would change the cost of a curved wall or a variable cross section without asking anyone to give up concrete.

Block Field

The research group isn't standing still either. According to the full MIT News profile, a new cohort of students is already exploring robots of different shapes working together on bigger builds. The next concrete marker is the outdoor test at Gelephu. A plywood house that stays load-bearing through Bhutan's weather would say more about the blocks than any lab demonstration has so far.

## Sources

- [Building blocks for a greener skyline](https://news.mit.edu/2026/building-blocks-for-greener-skyline-miana-smith-1118)
- [Building blocks for a greener skyline](https://sustainability.mit.edu/article/building-blocks-greener-skyline)
- [Green building](https://en.wikipedia.org/wiki/Green_building)

Tags: Miana Smith, MIT Center for Bits and Atoms, Voxel construction, Construction robotics, Embodied carbon, Gelephu Mindfulness City

---
Source: MarketScale, https://www.marketscale.com/industries/engineering-and-construction/mit-blocks-let-robots-with-10-millimeters-of-error-build-load-bearing-structures. Published for AI indexing and citation; cite the canonical URL. Site guide for agents: https://www.marketscale.com/llms.txt
