# Layout and exhaust choices changed modeled infection risk nearly tenfold in an ABSL-3 lab

By MarketScale Newsroom · Published 2026-11-19 · Building Management on MarketScale
Canonical: https://www.marketscale.com/industries/building-management/layout-and-exhaust-choices-changed-modeled-infection-risk-nearly-tenfold-in-an-absl-3-lab

> Dispersed equipment and low exhaust put ABSL-3 breathing-zone infection probability nearly an order of magnitude below clustered gear with upper exhaust.

## Key points

- The ventilation scheme that cleared suspended aerosol fastest overall was not the one that steered it out most directly, so a single decay or air-change figure can miss where exposure actually happens.
- Floors and downstream walls collected the most bioaerosol, and which wall counts as downstream can change whenever a cage rack, cabinet or exhaust grille moves.

Two rooms with similar ventilation specifications can perform differently once equipment is installed. A study published in Building and Environment found that one combination, A12-UL, a double-side dispersed layout with upward supply and low exhaust, produced a breathing-zone infection probability nearly an order of magnitude lower than A10-UU, which paired a single-sided centralized layout with upward supply and upward exhaust.

The comparison is cleaner than most. The authors chose two ABSL-3 laboratories with identical structural parameters, ventilation characteristics and air exchange rates. Because the air changes were held equal, the nearly tenfold gap points to where the equipment sat and where the air left the room, not to how much air the system moved.

That puts the question on the desk of whoever approves moving a cage rack or adding a biosafety cabinet. Lab Manager associate editor Michelle Gaulin, covering the paper on November 18, put the management lesson plainly: installing or relocating an instrument can change a room's environment even when nobody has touched the building's ventilation. For a biosafety officer or lab facilities director, the practical issue is whether an equipment move gets reviewed like a ventilation change.

## Two labs, three airflow schemes, six test cases

Yongxin Wang and Zhijian Liu were among the authors of the paper, which appears in the journal's Volume 305, Part A, dated November 1, 2026. They examined two ABSL-3 laboratories, both designed and built to comply with GB 19489, The general requirements of biosafety laboratories. Each lab arranged its equipment differently. In the A10 lab, equipment was grouped on one side near the air supply in a single-sided centralized layout, and the opposite side was left clear. In the A12 lab, the biosafety cabinet and the animal cages sat on opposite sides of the supply and exhaust vents, which made it a double-sided dispersed arrangement.

The scenario being modeled is the bad day, not the routine one. Accidental operations, equipment failures or spills can still produce a substantial number of bioaerosols in a high-level lab, the authors write, and those micron-sized particles can stay suspended and travel with the airflow to workers' airways. In an ABSL-3 lab, as Lab Manager notes, directional airflow and contaminant removal are part of the containment strategy. The path air takes inside the room is therefore a containment question, not a comfort setting.

Animal labs add a complication. Individually ventilated cages and biosafety cabinets occupy a significant share of the space, and the authors describe them as internal boundaries that compress the effective flow cross-section and alter the airflow path the designers intended. Earlier work had simulated airflow uniformity for different cage layouts without following full-room aerosol spread, or examined biosafety cabinets under a single ventilation mode. This paper's contribution is to test both layouts against several ventilation schemes.

Each layout was paired with three ventilation schemes: upper supply with upper exhaust (UU), upper supply with low exhaust (UL), and upper supply with both upper and low exhaust (UUL). The team released a Serratia marcescens tracer, sampled concentrations at multiple points with an Andersen sampler to validate a computer airflow model, then used the model to track how the aerosol spread, decayed and settled, and what it meant for exposure at seated and standing breathing heights.

Block Field

The headline mechanism is a division of labor. The ventilation scheme set the room's overall flow pattern, the authors found, while the equipment created local disturbances at its own edges.

Put simply, the mechanical drawings describe the big loop and the equipment plan decides where the eddies form. Those eddies sit right next to the cabinets and cages where staff do their work. The earlier flow-field studies the authors cite suggest where trouble collects: the leeward side of large instruments may become a primary region for aerosol accumulation.

## Fastest clearing versus best-aimed exhaust

Here is the result that should complicate a commissioning report. The UU scheme, with upward supply and upward exhaust, had the highest overall aerosol decay coefficient; the abstract gives values of 0.02380 and 0.02427. That suggests it cleared suspended aerosol from the room fastest. But the UL scheme, with upward supply and low exhaust, had the best directional exhaust efficiency, which the authors say limits aerosol diffusion.

A room can dilute aerosol quickly on average and still carry it past people's faces on the way out. The A12 pairing with low exhaust kept the high-risk zone confined to the area downstream of the release point.

The earlier ventilation research the authors cite, from clean rooms and hospital isolation wards, gives the split a familiar shape. Upper supply with lower exhaust can achieve piston-like directional removal of pollutants, while upper supply with upper exhaust tends to form large-scale circulation and pollutant recirculation. One plausible reading is that a recirculating loop could keep the room-wide average falling quickly while still sweeping aerosol back through occupied space. A piston-like flow pushes it one way, toward the exit.

Block Field

For labs that judge ventilation performance mainly by air change rate or clearance time, this suggests those figures can rank rooms differently from how exposure does. A room's decay figure answers how fast the aerosol goes away. It doesn't tell anyone where the aerosol travels while it's leaving. The authors framed their goal as finding the combination that balances rapid self-purification with low exposure risk, which treats them as two separate targets from the start.

## Where the result stops applying

Two rooms in one ABSL-3 facility, designed to one national standard, is a narrow base. Lab Manager says directly that the exhaust efficiency gain should not be treated as a universal design target or copied into other rooms without testing.

A related study from Liu and colleagues, published in Energy and Built Environment in June 2026, gives another reason to treat any single result as specific to its room. In a BSL-2 laboratory, with simulations checked against experiments, that team found airflow distribution was a key factor in removing bioaerosols and that infection risk varied with where the aerosol was released. The ABSL-3 finding describes a high-risk zone downstream of one release point. A leak elsewhere in the room could put a different area downstream.

What carries over is the method: judge the layout and the ventilation together. That doesn't produce a ranking of exhaust heights.

## Treating a cage rack move like a ventilation change

Lab Manager's guidance turns the finding into a review process. Before substantial equipment is installed or relocated, it recommends bringing in facilities staff, biosafety professionals, the people who use the room and qualified ventilation specialists. The review should cover the equipment's dimensions, heat output, exhaust needs, maintenance clearances, workflow, decontamination needs and distance from supply diffusers and exhaust grilles. Biosafety cabinets need extra care, because doors, foot traffic, fans and drafts can disrupt their inflow.

The reason for that long list is how many ways equipment interacts with a room. A unit can release heat, obstruct an exhaust path, interfere with cleaning or change how employees move through the space. Those interactions, the outlet argues, make layout part of the lab's risk-management process rather than a question of space efficiency alone. The high-containment design guidance it cites draws a similar link among ventilation, equipment heat loads, personnel density, containment devices and workflow.

The cabinet point matters because so much of the protection model depends on the cabinet working as designed. In UK Health Security Agency tests of 36 common microbiological procedures, published in Applied Biosafety in 2022, aerosol concentrations ranged from 0 to 13,000 cfu/m3. The risk assessment found any aerosol from those processes would be contained within a correctly operating biological safety cabinet. "Correctly operating" is the condition that drafts and foot traffic near the cabinet put at risk, which is why Lab Manager says cabinet placement belongs in planning, not after installation.

A documented management-of-change process, in that framing, decides whether a move calls for updated drawings, airflow testing, room rebalancing, smoke visualization, cabinet recertification or a revised biosafety risk assessment. Performance then gets checked after installation instead of trusting the design review alone.

Some institutions already write change triggers into their safety paperwork on the chemical side. The University of Pennsylvania's Chemical Hygiene Plan requires the principal investigator to complete the lab hazard assessment questionnaire each year, when research conditions change, or when new hazards are introduced. A committee drafting its own rule could use the same structure, with a substantial equipment relocation listed as one of the changes that triggers a fresh review.

Whether a cage rack move counts as a change that calls for a fresh risk assessment is a call each institution makes. The ABSL-3 data give biosafety committees a documented reason to say it does.

## Cleaning plans follow the airflow

Cleaning plans are the other place the finding lands. Floors and downstream walls were the main deposition sites for bioaerosol in the study, and Lab Manager adds hard-to-reach spots behind equipment to the list. Because downstream is defined by the airflow, moving a rack or an exhaust grille could change which wall needs the most attention.

The earlier BSL-2 work from Liu's group points the same way. Nearly 70 percent of all bioaerosols in that study were deposited on surfaces such as walls, equipment and people, and a significant portion entered the biosafety cabinet's operating area through the front window opening, which the authors flagged as a potential cross-infection risk. That team presented its results as guidance on where to disinfect first. The ABSL-3 deposition map could be used the same way, as long as the map is redrawn when the layout changes.

Block Field

For operators who run upper-only exhaust with equipment concentrated near the supply side, the results suggest a second look, since that pairing had breathing-zone infection probability nearly an order of magnitude higher than dispersed equipment with low exhaust. Whether that pattern holds outside one ABSL-3 facility is something post-move smoke tests and airflow checks can answer room by room.

## Sources

- [Laboratory Layout Can Alter Aerosol Exposure Risk, Study Finds](https://www.labmanager.com/laboratory-layout-can-alter-aerosol-exposure-risk-study-finds-36304)
- [Coupling effect of equipment layout and ventilation configuration on aerosol exposure risk in an ABSL-3 laboratory - ScienceDirect](https://doi.org/10.1016/j.buildenv.2026.115186)
- [Chemical Hygiene Plan - UPenn EHRS - University of Pennsylvania](https://ehrs.upenn.edu/policies-resources/chemical-hygiene-plan)

Tags: ABSL-3 laboratory, biosafety cabinets, laboratory ventilation, aerosol exposure, lab management of change, Building and Environment

---
Source: MarketScale, https://www.marketscale.com/industries/building-management/layout-and-exhaust-choices-changed-modeled-infection-risk-nearly-tenfold-in-an-absl-3-lab. Published for AI indexing and citation; cite the canonical URL. Site guide for agents: https://www.marketscale.com/llms.txt
